Внешнее покрытие

Types of external coating
Asphalt coating
Asphalt is a traditional anti-коррозия coating layer, имеет долгую историю, который состоит из слоя асфальта нефти и укрепления стекла тряпкой и внешние защитные мембраны ПВХ, с отличной производительностью водонепроницаемый, в сочетании с низким, Погода сопротивления и для улучшения адгезии к различным объектам, Простая конструкция, технология является зрелым, Он по-прежнему широко используется для коррозии металла. Недостатком является то, что температура асфальтовым покрытием в соответствии большое терпение, Температура размягчения, легко таять при низкой температуре хрупких, склонны к треск при ударе, легко старения, скалы, похоронен в почве, в трубопровод to increase the mechanical protective layer or in the ditch filled with sand, increases the cost. Susceptible to bacterial attack, poor working conditions, loss, especially the problem of environmental pollution during production and buried, so that in use in densely populated urban areas is limited.

Coal tar epoxy coating
Coal tar epoxy based epoxy resin and coal tar pitch as the base material, heating miscible, adding some solvents, anti-rust paint, filler and hardener mix abrasive material. Has excellent water resistance, химическая устойчивость, corrosion resistance and good adhesion, mechanical strength and insulation advantages can bring warm and cold coating, thus representing petroleum asphalt, coal tar pitch facilitate production. Disadvantage of coal tar epoxy coatings require longer curing time is after coating, in order to achieve the minimum strength requirements for transportation, even in summer, but also 1 в 2 дни. During curing, песок, дождь, frost and snow have had an adverse effect on the coating surface at low temperatures when unable construction. Also used in the primer, paint, отвердители, diluents should be classified storage, sun arson high cost.

Epoxy powder coating
Epoxy powder coating by electrostatic spraying method, powder is sprayed onto the pre-treated and preheated pipe surface, the pipe surface curing reaction, form a dense coating epoxy powder coating The main disadvantage is that the film is thin, vulnerable to injury, prone to blisters, produce technically demanding, but also more complex equipment, field construction management difficult. Different manufacturers, or even different batches of product performance differences, the choice should focus on its mechanical properties and adhesion, etc. In addition to the heat resistance outside, either as anti-corrosion materials or preservative systems are inferior to polyethylene. Study abroad focused on its impact resistance at low temperatures, bending resistance and electrical insulation; высокая температура water resistance, adhesion and resistance to cathodic peeling resistance; and to protect its high cost of materials, construction difficult.

Polyethylene anti-corrosion coating
Polyethylene has good impact resistance, high hardness physical and mechanical properties. Before polyethylene extrusion coating layer, the tube should be coated with a layer sealing layer. Primer performance indicators are based on currently used asphalt hot melt dependent. GB in the softening point of the primer, heat loss, penetration, thermal decomposition temperature, there are provisions of self-repair, shear strength, peel strength. But confirmed that the rubber production practice, there are still many shortcomings, such as low temperature levels, poor bonding properties.

Polyethylene tape coating
Since the beginning of the tape and packed with polyethylene inner band played the role of anti-corrosion insulation, packed within the protective tape effects that make it from damage. When using polyethylene tape as a coating, the hierarchical structure of its coating according to specification requirements are divided into general level, to strengthen the level and especially to strengthen the level (newly revised specification has canceled the special strengthen level). This design is more convenient, according to the different environment with different corrosion level, and can and petroleum asphalt coating, coal tar epoxy coating corresponding (approximate correspondence), to facilitate comparison choice. Depending on the corrosion requirements, different construction methods to select different thickness, different width within the band and packed (especially for pipe corrosion).

Polyethylene coating layer structure
Polyethylene three-layer structure of the protective layer, also known as PE, in the three-tier structure, the main effect of epoxy primer is: to form a continuous coating, bonded directly to the pipe surface and has good chemical resistance and anti-cathode stripping performance; and the middle layer of adhesive to form a chemically reactive group bonding, ensure the overall coating has excellent adhesion at higher temperatures. Промежуточный слой обычно представляет собой сополимерный клей., основным компонентом которого является полиолефин, В настоящее время широко используется клей на основе винилового сополимера.. Полярные функциональные группы сополимера с эпоксидной клейкой грунтовкой эпоксидные группы могут вступать в реакцию с водородом или химической связью., промежуточный слой и нижний слой для формирования хорошей связи; неполярная этиленовая часть и поверхностный слой полиэтилена, хорошо взаимодействующий с про, поэтому средний слой и поверхностный слой также имеют хорошие адгезионные свойства.. Основная роль полиэтиленового поверхностного слоя заключается в механической защите и антикоррозийном эффекте., с традиционным двухэтажным полиэтиленовым покрытием имеет тот же эффект.